Indesit washing machine makes noise during spin cycle
Vibration and noise during the spin cycle are inevitable with any front-loading automatic washing machine. After all, it's during the spin cycle that the drum rotates at its maximum speed, meaning the machine's body is subjected to strong centrifugal force, which it must simultaneously combat.
If the washing machine is installed incorrectly or is broken, for example, the unit will vibrate more, meaning the noise will be significantly louder. In this article, we'll discuss the causes of Indesit washing machine noise during the spin cycle and the problems that cause it.
Or maybe there is no reason to worry?
Suspicious women often contact service centers, vying with technicians to explain how horribly noisy their washing machines are. They claim they can't possibly be that loud, and that there must be a problem. The technician arrives, runs a test run of the washing machine, confirms everything is working properly, there are no problems, and the noise is within acceptable limits, takes the callout fee, and leaves.
In this case, it is important to understand that the noise sensitivity threshold is individual for everyone; some people react negatively to noise over 70 dB, while others tolerate noise over 130 dB. Before rushing to a service center, make sure that your Indesit washing machine model is, for some reason, louder than usual. It's not difficult to do this in our age. Just follow these steps:
- take the instructions that came with your Indesit washing machine;
- Find in the instructions the noise level in dB that the washing machine should produce during spinning;
The manufacturer always provides information about the maximum noise level of a washing machine, but if you don't have the instructions, you can look up the noise level of your washing machine model online.
- Download and install any free sound level meter utility for your smartphone (for example, we used the Sound Meter utility);
- Set up the utility according to the instructions that come with it, and measure the noise from the Indesit washing machine during the spin cycle.
Next, proceed based on the measurement results. If the dB value reported by the utility (+/- 5-7 dB) roughly matches the value specified in the instructions, then this noise level is normal for this model, and there's nothing you can do about it except replace the washing machine. However, if the readings vary significantly and the noise level exceeds the stated value by 15, 20, or even 40 dB, you need to investigate the cause—this is definitely not normal.
Even if the noise level during spinning is significantly higher than stated by the manufacturer, don't rush to call a technician or tamper with the washing machine. Observe how the machine operates when the drum speed reaches maximum, and, of course, pay attention to how much laundry you're loading and how you're doing it. It's quite possible that the problem isn't the machine itself, but rather a simple user error or improper installation. I'd like to discuss installation in a bit more detail.
Installation defects
To ensure your washing machine works properly and doesn't make unnecessary noise, it's essential to meticulously install it. Many users neglect installation instructions, believing it's pointless to spend time studying them. As a result, our technicians, when visiting clients' homes, are left scratching their heads when they see washing machines installed at an angle of 10 degrees, or even worse, when the owners forgot to remove the shipping bolts and continue using them as if nothing had happened.
Remember! Failure to properly install your Indesit washing machine will void the manufacturer's warranty. We have no doubt that after such installation, your machine will soon need repairs.
Before placing your Indesit washing machine anywhere, make sure it has the strongest possible foundation. A concrete floor is ideal, but if a concrete base isn't possible, at least reinforce a wooden floor so it doesn't wobble or sag, even when you jump on it. If a floor can withstand a jumping adult man, then it can easily withstand a working washing machine.
Once the floor is secured, you can begin installation, but be sure to always have a level handy. Even the slightest misalignment of an Indesit or any other washing machine will affect its operation. Also, remember to remove the shipping bolts located in the designated holes on the back of the washing machine.
You can even install a washing machine on an old wooden floor, as long as you properly reinforce it first and everything will be fine.
If you're installing a washing machine under a countertop, in a sink, or other furniture, remember to leave a 1 cm gap between the walls of the furniture and the washing machine, and a 2 cm gap between the side walls. Ideally, the washing machine shouldn't touch the furniture at all, so that vibration isn't transmitted to it and can have a detrimental effect.
These are just some recommendations regarding the correct installation of a washing machine, if you need more details, read the publication Installing and connecting a washing machineYou will find a lot of useful information in this article.
Foreign object or manufacturing defect
If your Indesit washing machine is very noisy right out of the box, you should listen very carefully to the sound. If the noise is consistent and simply exceeds the manufacturer's stated level, it's not a big deal, although even then you may be able to request a warranty repair or a replacement. However, if the noise is uneven, with a metallic clanking sound audible through the hum and rumble, you should immediately stop the washing machine, drain the water, and call a technician. Washing under these conditions is strictly prohibited.
Don't even think about messing with the body of a new Indesit washing machine while it's still under warranty. Let a service technician investigate the noise during the spin cycle. It's likely a manufacturing defect, perhaps faulty bearings or other moving parts. In any case, the specialist in charge will handle the investigation.
It's possible that your old Indesit washing machine was working fine, but then suddenly started making a loud clanking noise during the spin cycle. In this case, you don't necessarily have a malfunction; it's quite possible that a large foreign object has simply gotten into the drum. It's not always possible to tell by the sound without being an experienced technician, but there are some telltale signs. Let's look at them.
- Along with the noise and clanking, you can also hear the characteristic jamming of the drum during the spin cycle.
- When the machine is running at high speeds, a foreign object will dangle in the tank; if you listen closely, you can hear it.
- You can shine a flashlight into the small holes in the drum and try to see what is at the bottom of the tank. You can also move the edge of the cuff and look with a flashlight into the gap between the tank and the drum.
It is very difficult to see anything through the gap or perforated walls of the drum, but you can try, and sometimes it works.
Let's imagine you've seen, heard, or simply remembered something foreign that might have disappeared into the depths of your washing machine's tub. What should you do in this case?
- We remove the back wall of the “home assistant”.
- We remove the drive belt.
- We take a photo with a smartphone of the location of the wires on the heating element, which is located at the bottom of the tank.
- We remove the wires, unscrew the nut located between the heating element contacts, and pull out the heating element.
- We reach into the hole that was formed after removing the heating element and scoop out all the dirt from the bottom of the tank along with the foreign object.
- We put the heating element and other parts in place, assemble and install the washing machine.
Possible breakdowns
If the drum of your Indesit washing machine rattles and the casing vibrates during the spin cycle, this could indicate a serious malfunction. Most often, abnormal noise in Indesit washing machines during the spin cycle occurs due to a damaged bearing. This is a rather unpleasant situation that can lead to expensive repairs, although, of course, you can replace this part yourself. It's not easy, but if you read our article, you can find out. How to change a bearing in an Indesit washing machine, you can definitely do it.
Noise can also be caused by a deformed pulley or spider, although with such damage a strong, unpleasant sound will still be noticeable during washing. In general, it is very difficult to determine anything by sound in such a situation; you need to open the case and take a look, and it is better if a professional does this.
In conclusion, an Indesit washing machine can make loud noises and other loud, unnatural sounds for a variety of reasons. This could be due to simple overloading, an unbalanced drum, or a serious malfunction. In any case, it's best to address the issue immediately, without delay, and perhaps your "home helper" will continue to work for a long time. Good luck!
Interesting:
3 reader comments
Add a comment
Headings
Washing machine repair
For buyers
For users
Dishwasher
Thanks, it looks like the bearing is broken.
Can you tell me what set of tools is needed to disassemble it and adjust the drum!?
Good evening! We changed the bearings, but there's still a knocking noise and the water isn't heating. Could you tell me why?