Electrolux Washing Machine Error Codes

Electrolux washing machines Washing machine error codes are necessary to simplify diagnostics.

Using them, we can easily understand what is broken in our household appliances.

This approach is quite convenient. So, let's get down to business.

Codes

Code	Code interpretation	Why did the error occur and how can I fix it?
E11	The machine doesn't fill with water during programs. The required amount of water didn't reach the required level within the required time.	The most common cause of this error is a faulty water inlet valve or triac. Make sure the winding resistance is approximately 3.75 kOhm. In addition to the reasons listed above, this problem may occur due to low water pressure in the water supply system, a lack of water in the pipes, or a clogged filling system.
E13	There was a leak. Liquid got into the machine's tray.	Make sure there is indeed water in the pan. Find and fix the leak.
E21	The water was not drained from the washing machine within the set time (10 minutes).	The drainage system (pipes, filter, pump) is clogged. The drain pump is out of order. Make sure that the winding resistance of the drain pump is approximately 170 ohms. The breakdown could have occurred due to a failure of the electronic module.
E23	The pump control triac is broken.	Confirm the fault by checking the triac. If faulty, replace it.
E24	Violation of the integrity of the pump's thyristor circuit.	Make sure there is a breakdown and fix it.
E31	Level relay failure.	Replace the level sensor. Conduct a check and if a fault is found, replace the wiring.
E32	Erroneous data from the pressure switch	It's possible you forgot to turn on the water supply valve, or the water pressure is too low. Or maybe the water has been turned off. Clean the inlet filter mesh of the inlet valve. Replace this valve. Try changing the level relay tube. Replace the relay itself.
E33	Incorrect or inconsistent operation of pressure switches (1st level relay and heating element protective relay).	Here are the most common ways this situation can arise: The sensor tubes(s) are clogged. The pressure switch or heating element relay has become faulty. Excessive voltage in the electrical network.
E34	Mismatch between the level relay data and the second level of anti-boiling.	If the error appears for more than one minute: Replace the level relay tube. Replace the pressure switch. Make sure the wires and contacts are intact.
E35	Too much water in the machine	There's too much water. It's reached the maximum level. Check the level switch and, if it's broken, replace it.
E36	Heating element level protection relay failure.	Make sure there is a malfunction.
E37	The 1st water level relay is broken.	Perform a check of this part.
E38	There is no signal about a change in pressure (probably the pressure switch tube is clogged)	Clean/change the tube.
E39	The overflow pressure switch is broken.	Conduct a test of this device.
E3A	Heating element relay failure.	It needs to be changed.
E41	The machine door is not closed tightly enough.	Open and close the door again.
E42	UBL failure.	Check and replace the door locking device if necessary.
E43	The control thyristor of the door lock is broken.	Make sure it is faulty and replace it.
E44	The door opening sensor has become faulty.	Make sure that this fault is present.
E45	Parts of the UBL thyristor circuit have broken.	Perform a check of these parts.
E51	The electric motor's thyristor short-circuited.	Conduct a malfunction check. If the problem is confirmed, replace the broken part.
E52	The electric motor tachometer does not transmit data to the controller.	One of the most common causes of the "E52" code is a loose mounting washer. This can cause the coil to become dislodged, resulting in this malfunction. This can be corrected by replacing the coil and washer, or by replacing the tachometer.
E53	Parts of the control circuit of the electric motor's thyristor have failed.	These parts are checked and, if any damage is detected, they are replaced.
E54	The contact group of the reverse relay (there are 2 of them in total) has ignited.	Check and replace the part if there is a fault.
E55	Open circuit in the electric motor	Check and correct the wiring. Conduct a check and change the engine.
E56	No data is received from the tachometer generator.	Replace the specified spare part.
E57	Electricity more than 15 amps.	Check and replace the wiring if necessary. Check and, if faulty, replace the electric motor. Check and replace the electronic module if necessary.
E58	The electric motor's current is higher than 4.5 amperes.	Engine change. Checking and, if necessary, replacing the wiring. Replace the electronic module.
E59	Within 3 seconds from the moment the command to start the engine is given, there is no signal from the tachometer.	Conduct a wire check. Replace the tachometric generator. Replace the electric motor. Replace the electronic module.
E5A	The cooling radiator has heated up to over 88 degrees.	Replace the electronic unit.
E5B	The electrical voltage drops below 175 V.	Check the wires. Replace the electronic unit.
E5C	The electrical voltage in the bus exceeded 430 V.	Replace the electronic unit.
E5D	FCV does not receive / send data for 2 sec.	Replace the electronic unit.
E5E	Problems in communication between FCV and main printed circuit board.	Replace the electronic unit.
E5F	FCV control board It makes configuration requests non-stop. This is because it's constantly resetting.	Check the wiring for proper operation. Replace it if necessary. If that doesn't help, replace the electronic unit.
E61	During the heating process, the water does not reach the temperature required to complete the program within the required period of time.	This error only appears in the washing machine's diagnostic mode. Make sure the heating element (TEN), its contacts, and wires are working properly.
E62	The water heated up to over 88 degrees in five minutes.	Make sure the heating element is working properly (there's a possibility of a breakdown in the housing). However, this code most often appears when the temperature sensor fails. The temperature sensor should be tested with a multimeter. If the resistance is between 5.7 kOhm and 6.3 kOhm, it's OK.
E66	The heating element relay is out of order.	Check the wiring, circuit, and relay for this component. If anything is faulty, replace it.
E68	Leakage current is too high	Replace the heating element or other components.
E71	Temperature sensor overvoltage	Most likely, there was a break in contact or a short circuit in the sensor and/or circuit.
E74	The temperature sensor is not positioned correctly.	Make sure it is in a normal position.
E82	Violation in the selected selector location.	The electronic unit, wiring or selector is faulty.
E83	The signal from the selector is not identified.	This code appears only in the machine's diagnostic mode. Incorrect configuration, replace the unit.
E84	The recirculation pump is not identified.	Replace the electronic unit.
E85	Recirculation pump failure.	Replace the pump or electronic unit.
E91	Problems with communication between the interface and the main unit.	The electronic unit needs to be replaced.
E92	There are problems of correspondence between the main block and the interface.	The electronic unit needs to be replaced.
E93	Problems with the machine configuration.	It is necessary to enter the correct configuration code.
E94	Incorrect configuration of the machine and execution of the specified program.	Rewrite volatile memory or change the circuit.
E95	Problems of communication between volatile memory and processor.	Ensure that there is power supply to the volatile memory board. Check the integrity of the circuit between the EEPROM and the processor.
E96	Mismatch between the configuration data of the electronic controller and the connected/unconnected elements.	Conduct a check for compliance/non-compliance of connected elements.
E97	Problem with matching software between the electronic controller and the software selector.	The machine may be incorrectly configured. Replace the main unit.
E98	Problem of correspondence between electronics and electric motor control unit.	Check the wiring and replace it if necessary. Make sure the electronic unit is working properly. If not, replace it.
E99	Incorrect connection of electronics and sound of the unit.	Replace the unit. Check the wiring.
E9A	Software corruption between electronics and speaker.	Replace the electronic unit.
EA1	Incorrect functioning of DSP.	Check the wiring. The main unit may need to be replaced. Replace the DSP. Replace the engine drive belt.
EA2	Problem with DSP identification.	The main unit needs to be replaced.
EA3	DSP does not lock the engine pulley.	Check and replace the wiring. Check and replace the engine drive belt. Replace the DSP. Replace the main unit.
EA4	The DSP is out of order.	Check the wiring. Replace the main unit. Replace the DSP.
EA5	The DSP thyristor has failed.	Replace the main unit.
EA6	No data on drum movement during 30 seconds from start.	The drum doors are open (on a vertical machine). The engine drive belt needs to be replaced. The DSP needs to be replaced.
EB1	The power grid frequency does not match the required one.	The electrical network needs to be checked.
EB2	Excessively high voltage.	Conduct an electrical network check.
EB3	Excessively low voltage.	Perform a power grid check.
EBE	Protection circuit relay failure.	The electronic unit needs to be replaced.
EBF	Problem with protection circuit identification.	The electronic unit needs to be replaced.
EC1	The fill valve is stuck.	Replace the wiring. Replace this valve. Repair/replace the wiring.
EC2	A malfunction related to the sensor responsible for the purity of the liquid.	Change it.
EF1	The machine takes too long to drain water.	Make sure the pump is working properly. Clean the inlet hose and the entire system.
EF2	Excessive foaming when draining water. The drain hose is clogged. The drain pump filter is clogged.	Make sure the pump is working properly. Use only detergents intended for machine washing. Do not overfill the dispenser. Clean the pump filter and drain hose.
EF3	The water control system has been activated. There is a problem with the pump wiring. There is a break in the pump. There is a leak.	Replace the pump. Repair the wiring. Inspect the machine for leaks.
EF4	No data is received from the flow sensor when the fill valves are activated.	The water supply is blocked or there is no water in the water pipes.
EF5	Emergency stop of the spin mode due to a significant imbalance of items in the tank.	Make sure you don't load more items than recommended for your machine. Make sure your machine works properly with a smaller load.
EH1	The voltage frequency is not within the norm.	Problems with the electrical network. Electronic components may need to be replaced.
EH2	The voltage is too high.	Replace the electronics.
EH3	Excessive voltage.	Replace electronic components.
EHE	The protection circuit relay has failed.	Replace the electronic unit.
EHF	Problem with protection circuit identification.	Replace the electronic unit.

Interesting:

10 reader comments

September 18, 2015 at 8:35 AM
Rediska26:

I have an EWS 11600 W. It announced the end of the wash cycle a few seconds after starting it. An autopsy revealed that a wire had simply fallen off the drain pump. It's easily fixed, of course, but it's unclear why the machine didn't report the error. Is this a firmware glitch, or are special conditions required for the error to appear?

Answer
December 18, 2016 at 9:18 PM
Valya:

We are getting errors E40 and E80, but they are not on the list. What do they mean?

Answer
- January 6, 2017 at 4:16 PM
  Anonymous:
  
  Change the lock.
  
  Answer
October 4, 2017 at 11:03 PM
Max:

EF0 – what's the error? It doesn't go into the rinse cycle after washing.

Answer
October 23, 2017 at 2:47 PM
Anonymous:

I have received an error regarding the EAO. What should I do?

Answer
November 3, 2017 at 3:28 PM
Dmitry:

It gives error E 40 every time, what should I do?

Answer
December 2, 2017 at 10:46 PM
George:

The Electrolux is displaying an EF5 error code. The drum isn't spinning. I can hear the drain pump running, but no water is draining. What should I do?

Answer
December 19, 2017 at 11:19 AM
Sergey:

Error e 90, what to do?

Answer
May 5, 2019 at 2:20 PM
Igor:

EWT 815 vertical, the bottom LED blinks 5 times. What is the error?

Answer
April 24, 2020 at 8:46 PM
Faith:

Indesit IWSE 6125.
I have an F12 error, and it's not listed either. What should I do? All five lights are on, and they were blinking at first. Then I closed the door, and they just stayed on.

Answer

Electrolux Washing Machine Error Codes

Codes

Interesting:

Add a comment