Atlant washing machine error codes
Most new home appliances have several important features.
In addition to their direct functions, they also inform about any malfunction that is preventing them from working properly!
Let's move on to a description of washing machine error codes.
Error codes
| Error signaling | Transcript | Malfunction options | Repair |
| On a machine with a display "Sel"On a machine without a display: the indicators do not light up. | Interface module selector failure | The potentiometer that selects programs may be broken. | Changing the interface module. |
| On display: NoneIf there is no display, all indicators light up. | Excessive foam formation. | Too much powder was used for washing. | Limit the amount of washing powder to a smaller amount. |
| An incorrect mode has been set. That is, a mode with an excessive amount of water added. | Select a washing mode that is suitable for the given type of fabric. | ||
| The washing powder or other detergent used is not suitable for machine washing. | Use only those detergents and powders that are intended for machine washing. | ||
| Display: F2The third LED lights up. |
The temperature sensor is out of order. | Problems with the wiring and contacts of the temperature sensor or module. | Make sure that the wires and contacts are in good condition. |
| The temperature sensor is broken. | Replace the heating element. | ||
| The control module has failed. | Replace the faulty module. | ||
| Display: F3The 3rd and 4th indicators are lit. |
The heating element of the washing machine has failed. | Heating element failure. | Replacing the heating element (TEN). |
| Broken contacts or wiring. | Make sure the wires and contacts are in good condition. | ||
| The control module has failed. | The module needs to be replaced. | ||
| On display: F4The 2nd LED lights up |
Drain pump failure | The drain hose is clogged or pinched. | Straighten the hose, find and remove the blockage. |
| Incorrect installation of the hose. | Reinstall the hose as directed in the instructions. | ||
| If a foreign object gets into the pump, its impeller will become blocked. | Remove the object and check the impeller rotation. | ||
| Drain pump failure. | Replace the broken pump. | ||
| The ball in the drain coupling has ignited. | Drain the water from the machine using a tube and replace the coupling. | ||
| The drain coupling is clogged. | Perform cleaning. | ||
| Problem with wiring and contacts. | Make sure both are in good working order. | ||
| The electronic module has failed. | Replace the electronics module. | ||
| Display: F5The 2nd and 4th indicators are lit. |
Fill valve failure | The water inlet hose filter is clogged. | Cleaning the filter. |
| The inlet hose is clogged or pinched. | Unscrew the hose from the machine. Turn on the water to check. Clean the hose if necessary. | ||
| There is no water in the water supply system, the water supply to the tap is not open, or the inlet valve is broken. | Make sure the faucet is open. Make sure the water supply isn't shut off. Replace the valve if necessary. | ||
| Open circuit between control module and fill valve. | Use a tester to check whether there is a break or not. | ||
| Violation of the contacts of the inlet valve | Make sure the contacts are in good working order. | ||
| Control module failure. | Replace it with a new one. | ||
| Display: F6The 2nd and 3rd indicator lights up | Problems with the washing machine's electric motor relay | The stator winding is overheating. The contacts responsible for the motor's thermal protection are disconnected. | Change the car engine. |
| Display: F7The 2nd, 3rd and 4th indicators are lit. |
Electrical problems | Interference filter failure | It needs to be changed. |
| The voltage in the network does not correspond to the required one (more or less). | Perform a network test using a tester. | ||
| The control module is broken. | Carry out its replacement. | ||
| Display: F8Indicator No. 1 is on | There is too much water in the washing machine tank. | Pressure switch failure. | Replace the pressure switch. |
| The fill valve is stuck. | Replace the valve. | ||
| Problems with the wiring or contacts of the pressure switch and control module. | Make sure that the wires and contacts are in good condition. | ||
| Cylinder leak. | Conduct a cylinder check. | ||
| The control module is broken. | Replace it with a working one. | ||
| Display:"F9»Indicators #1 and #4 are lit. | Problems with the engine tachometer | Broken contact or wiring of the electric motor or control module. | Check the presence or absence of a problem by checking the wires and contacts. |
| The engine or tachogenerator is broken. | Change the engine. | ||
| The control module has failed.. | Replace it with a working one. | ||
| On display: F10 If the machine does not have a display: indicators #1 and #3 light up. |
Breakdown of the UBL (lock) | Malfunction in the lock. | Replace it with a new one. |
| Control module failure. | Replacement. | ||
| Message on display: doorThe 1st, 3rd, and 4th indicators light up | The lock (UBL) may be broken. | No contact in blocking. | Make sure the wires are connected correctly and there are no breaks. |
| The hatch is not locked tightly enough. | Lock the hatch again. | ||
| The door or lock is warped. | Straighten the hatch / lock. | ||
| Open circuit between the control module and the door lock. | Use a tester to perform a circuit check. | ||
| Problem with the lock connector. | Make sure the wires are connected correctly and are intact. | ||
| The control module has failed. | Change it. | ||
| Display: F12The 1st and 2nd indicators are lit | The engine triathlon may fail. | The car's engine broke down. | Carry out replacement. |
| Open circuit in the motor winding. | Replace the engine. | ||
| No contact. | Make sure the wires and connector are in good condition. | ||
| The control module is broken. | Change it. | ||
| Display F131st, 2nd, 4th indicators are lit | Various breakdowns | Problems with wiring or contacts. | Check the wires and contacts. |
| The control module is broken. | Replace with a new one. | ||
| On display: F141st and 2nd indicators | Program crash | A program error occurred. The electronics module was programmed incorrectly. | Replace the module. |
| Display: F15 | A water leak has been detected | The tank became depressurized. | Carry out its replacement. |
| Leak through a closed door | Replace the hatch cuff. | ||
| Violation of the sealing of the drain hose, pipes, drain coupling | Try to locate the leak and fix it. Make sure the clamps are securely fastened to the pipes. Check the integrity of the pipes and drain hose. |
Interesting:
18 reader comments
Add a comment
Headings
Washing machine repair
For buyers
For users
Dishwasher
I've had my Atlant washing machine for five years now. No complaints. If I ever replace it, it will only be with an Atlant. I also bought an Atlant refrigerator in 2010. No complaints either; it works perfectly. Keep up the good work, guys. Well done. I'm from Donetsk. Thank you for a great product.
third breakdown in two years—module!!!!
It all depends on karma. I also have an Atlant washing machine and a freezer. Everything works.
7 months error 15 service helpless
The washing machine is 5 years old and hasn't had a single problem. It's just a little noisy. The refrigerator is the same. Well done!
My Atlant washing machine was fine for 6 years. I turned it on during a wash cycle and it showed the end of program and a lock. It won't clean or start. What should I do? Help!
It worked for four years and then the module failed. They replaced it, then soldered the tank. Basically, there's nothing left to fix. Better to buy a new one. I understand that these days, all machines are no more than five years old, and they all need a new one. That's the policy.
I don't know what to do. The washing machine keeps giving me an F8 error. It worked perfectly before it shut down. I bought it as a spare because I need a large washing machine that does laundry constantly. Now the main one is broken, and this one keeps saying there's too much water in the drum, which shouldn't be the case. It's been standing there for four years.
Error f16, what is it?
My Atlant washing machine is displaying error code f13. Indicators 3, 4, and 6 are lit. What should I do? What's the cause? Any advice?
I get an error message n, what does this mean?
This is not an error, but a night wash mode.
No karma! In a year and a half, the washing machine has broken down four times. Before, I managed without a repairman, but now I can't even find the error code P. Thank you, domestic manufacturer!
Nadezhda, the "n" isn't an error; the "night wash" option is enabled. There's a button on the control panel—you can use it to turn the option on and off. 🙂
f13 — change the control module, the firmware has crashed.
F16 — the heating didn't turn off. Replace either the control module or the heating element. It's impossible to diagnose remotely which.
The display shows error P. The door is locked. What should I do?
The display shows n-24