Whirlpool Washing Machine Error Codes

• Make sure the water supply is not shut off. That is, the tap is in the open position.
• Make sure the inlet hose isn't kinked or clogged. Inspect the inlet valve strainer. It's located where the hose meets the machine.
• Make sure the fill valve is working properly.

If there is water in the machine's tank:

• Make sure that the pressure switch tube is not clogged and is securely connected to the level relay and to the washing machine drum.
• Make sure the drain pump is not broken.
• Make sure the pressure switch is working properly.
• Make sure that the electronic module is not faulty.
• Make sure that the pressure switch (level sensor) is functioning properly.
• Inspect the siphon for blockage.
• Inspect the hoses, there may be water leaks.

• Make sure that the drain pump is not broken and is working properly.
• Inspect the wiring and contacts.
• Inspect and clean (if necessary) the drain pump filter. A clogged filter may be preventing water from draining.
• Make sure the drain hose is not pinched, kinked or clogged.
• If you have done everything, but this error occurs again when you start washing, then you should replace the pump.

• Make sure that the sensor is securely connected to the heating element and relay.
• Make sure the sensor is working properly.
• Make sure the heating element, its wiring and relay are working properly.

• Make sure that the washing machine motor is working properly.
• Make sure there is no break in the circuit between the engine and its control panel.
• Make sure there is no open circuit between the engine control panel and the electronic module.
• Make sure the electric motor control panel is working properly.
• Make sure the wiring is intact.

• Make sure the electric motor control panel is working properly.
• Make sure the electric motor is in good working order.
• Make sure there is no damage to the wiring.
• Make sure that the contacts between the engine and its control panel are good.
• Make sure the contacts between the motor control panel and the main control panel are good.

• Make sure that the wiring and contacts of the drain pump, control panel, and pressure switch are in good condition.
• Make sure the drain pump filter is not clogged.
• Check the drain hose. It should not be pinched or clogged.
• Make sure the drain pump is working properly.
• Check the pressure switch (level relay).
• Make sure the fill valve is working properly.

• Perform an engine check.
• Make sure the engine control panel is working properly.
• Check the location of the washing machine. It should not be located near a radiator. It is also advisable to have adequate ventilation in the room.
• Make sure the contacts and wiring are in good condition.
• Make sure that moving parts have not become damaged.

• Make sure that moving parts are not worn out and are working properly.
• Check the wiring and contacts.
• Make sure the electric motor is working properly.
• Perform a check of the engine control panel.
• Make sure that the central control panel is not broken.

• Check the dispenser motor.
• Inspect the dispenser and its motor for mechanical damage.
• Make sure the contacts and wiring are in good condition.

• Make sure the main control panel is working properly.
• If the problem was caused by power surges, then perhaps turning the machine off for a couple of minutes and turning it on again will help.

• Make sure the wiring and other connections are intact.
• Check the washing machine's electric motor.
• Make sure the drive belt is in place and not worn.
• Check the electric motor control panel.

• Make sure that the drain pump and pressure switch are working properly.
• Check the drain hose for kinks or blockages.
• Make sure the main control panel is working properly.
• Make sure the drain pump filter is not clogged.
• Check the wiring and tightness of the contact connections.

• The lock is faulty or missing.
• Check the integrity of the contacts and wiring of the drain pump, main control panel and peristaltic.
• The UBL (washing machine door locking device) or its wiring may be broken.

• Check the wiring from the control panel to the door lock.
• The lock may fail.
• Also make sure that there are no foreign objects in the lock mechanism and UBL.
• Make sure that the hatch locking device (UBL) is in good working order.