Ardo top-loading washing machine breakdowns

Washing machines from different brands have their own advantages and disadvantages. These should be taken into account when choosing your new home appliance. Knowing the weaknesses of a specific washing machine can help you avoid some breakdowns and extend its lifespan.

Let's look at common faults with Ardo top-loading washing machines. We'll explain the most common issues users encounter and explain how to troubleshoot them at home.

A broken latch causes the drum to jam.

Every third owner of an Ardo vertical storage unit contacts the service center with a similar problem. The drum spinning is the most common problem with top-loading washing machines. The user lifts the lid, opens the doors, and sees not the opening of the drum, but a metal wall.

Most often, the tank spins due to a faulty shut-off mechanism or loose closing of the valves.

Returning the drum to its normal position isn't easy, but it's possible. So, don't immediately call a service center. Calling a technician will be quite expensive. To rotate the drum, follow these steps:

• take a long metal wire with a diameter of 3-6 mm;
• bend one end of the wire to make a hook;
• lower the wire with the catching end down;
• hook the sash and try to close the drum sashes;
• After closing the doors, rotate the drum until the hatch is in the desired position.

The main difficulty is that you have to work blindly. If the hole in your Ardo model is too small and you can't get the wire down, try widening the "entrance" and try again.

If turning the drum with a wire doesn't work, there's another, more complicated method. You'll have to disassemble the vertical tank, access the flaps from the side or bottom, close them, and return the tank to its proper position. However, in most cases, users can fix the problem with a "hook."

Weak control module

Owners of Ardo top-loading washing machines often encounter a very frustrating problem: a broken control module. The machines either freeze mid-cycle or abruptly interrupt a running program. Sometimes, the washing machines "delight" users with sticking buttons on the control panel—in this case, one or two modes may not activate, while the control panel responds to other commands without issue.

It is better to entrust diagnostics and repair of the control board to service center specialists.

Repairing the main control unit is quite complex. Without experience working with electronics, it's impossible to handle such a task. Therefore, to avoid making the situation worse, it's best to contact a professional.

Repairs typically involve reprogramming the board or replacing semiconductor components. Contact corrosion or terminal problems are also possible. In any case, diagnostics of the unit will be required.

Washing machine owners can protect their equipment from breakdowns of this kind. The electronics in Ardo automatic washing machines are sensitive to power surges, so it's best to install a voltage stabilizer to absorb any power surges. This is exactly the case when it is easier to prevent a problem than to solve it later.

Let's pay attention to the bearings

Another common problem is bearing failure. The seal that protects the rings from moisture dries out, allowing water to seep in. As a result, the lubricant is washed out, the unit breaks down, the tub becomes loose, and the machine begins to rattle and bang during operation.

The main sign of broken bearings is a rattling and knocking noise during machine operation, which intensifies during the spin cycle. It's easy to check this suspicion. Open the drum and spin it by hand. If there's noticeable play in the drum or if it squeaks when rotating, the bearings need replacing.

To repair the unit, you'll have to completely disassemble the washing machine and remove the drum. First, remove the top cover of the washing machine, then disconnect all the main components from the plastic drum: the motor, pump, gearbox, and starting capacitor. Once the drum is clear, the component is removed from the machine.

The next stage of the repair is dividing the drum in half. Ardo washing machines don't have a separate drum, so you'll need to get creative. Technicians use a hacksaw to cut through the plastic drum—this is necessary to access the bearings.

After splitting the tank in half, remove the oil seal and knock out any damaged metal rings. If the bearings are stuck, pre-treat them with WD-40. Afterward, replace the components along with the oil seal.

Next, you'll need to connect the two halves of the tank. Typically, technicians seal them with sealant, soldering the parts together, and securing them with screws. Afterward, the washing machine is reassembled in reverse order. Then, run a test cycle. Monitor the machine closely to ensure the tank doesn't leak.

   

Readers' comments