Error E10 in a Midea washing machine

One of the main advantages of modern washing machines is their intelligent self-diagnostics feature, which promptly alerts the user if something is wrong. The E10 error in a Midea washing machine is familiar to many housewives, as it indicates that the machine is unable to fill with water for some reason. This could be due to anything from a damaged water line or a clogged inlet valve to a faulty pressure switch. In this article, we'll explore this error and examine all possible causes.

Let's start with simple faults

If the error code E10 appears on the display, this does not mean that your “home assistant” needs complex repairs. First of all, it is necessary to rule out the simple inattention of the owner of the appliance and check whether there is water in the house at all, whether the pressure is sufficient and whether the water supply valve to the washing machine is not closed. Check the machine's door; it must be slammed shut to activate the door lock and allow liquid to fill the drum. If everything is in order, you can proceed to inspecting the appliance, which will require partial disassembly. It's always best to start with the simplest parts, gradually moving on to hard-to-reach components.

Be sure to disconnect your Midea washing machine from all power sources before beginning any diagnostics or repairs.

First, you should check the inlet hose; problems with it are indicated by an unusual buzzing sound when attempting to fill with water. All you need to do is loosen the clamp, disconnect the hose from the machine, and carefully inspect it for damage. If everything is in order, rinse it under a strong stream of hot tap water and test the washing machine. If the problem wasn't with the inlet hose, you should inspect the filter element, which looks like a small mesh that often becomes clogged with scale and dirt, preventing water from entering the machine. What should you do to check it?

• Disconnect the inlet hose from the appliance.
• Locate the mesh located near the valve.
• Fix the protruding part of the filter with pliers.
• Pull the mesh gently towards you to remove it.
• If the stains are not severe, rinse it with hot water; otherwise, leave it to soak in a citric acid solution for several hours.
• Install the part in its place.

It's also worth examining the coarse filter installed in the water pipe behind the faucet. This attachment is essential for primary water filtration, so it retains most of the dirt and impurities. This filter can only be cleaned after securing the joint with one wrench and loosening the nut holding the flywheel with a second wrench. Be sure to place a large container under the liquid to prevent the powerful stream of water from damaging your floors and your neighbors' ceiling. There's no need to clean the mesh, as the water flow will remove all impurities, so all that needs to be done after this is to restore the water pipe to its original appearance.

Let's pay attention to the inlet valve

The E10 error code often indicates a problem with the inlet valve. This component of a Midea washing machine cannot be repaired, so if damaged, it must be replaced with a new one. This can be easily done yourself, even without calling a technician—just follow our instructions carefully.

• Make sure the machine is not connected to the water supply or electricity supply.
• Remove the top panel of the CM, which usually involves removing the retaining bolts from the back panel and then sliding the cover back, lifting it slightly.
• Disconnect the drain hose from the unit and drain the remaining waste liquid from it.
• Locate the intake valve and disconnect all wires from it.

Be sure to take a photo of the wiring before disassembling the part so that you have an example of the correct connection at hand during reassembly.

• Disconnect all connected pipes and drain the water from them.
• Loosen the bolt securing the inlet valve.
• Remove the valve.
• Install a new valve in its place and secure it with a bolt.
• Connect all wires and pipes.
• Replace the washing machine lid.
• Return the filling sleeve.
• Connect the washing machine to the power supply and water supply.
• Perform a test wash to check functionality.

Try to buy only original Midea parts to ensure your appliances last a long time. The easiest way is to take the old part with you to the store and use it as an example, but you can simply write down the serial number of the machine.

Let's move on to the pressure switch

What should you do if you've checked all the steps described above but still haven't identified the cause of the malfunction? Most likely, the problem lies in the pressure switch, which is also easy to check at home without calling a service center technician. All you need to do is carefully read our instructions and follow each step carefully.

• Disconnect the Midea washing machine from all communications.
• Remove the top case panel by removing the fasteners.
• Find the pressure switch.
• Prepare a tube the size of which will be similar to the diameter of the fitting.
• Disconnect the pressure hose, insert the prepared tube into it and gently blow into it.
• If the fluid level switch is OK, you will hear one or three quiet clicks.
• Finally, inspect the element to see if it is damaged or if the hose is clogged. If it is clogged, clean it with a powerful jet of water.

If there's no visible damage to the pressure switch, you'll need a standard multimeter set to resistance measurement mode for further inspection. Connect the device's probes to the level switch contacts and read the resulting value. If the reading changes after the measurement, the pressure switch contacts are OK. If the resistance remains the same, the part needs to be replaced.

You can do this yourself without calling a repair service. First, you need to buy a similar part. You can use a faulty fluid level switch or write down the exact model name of your washing machine. Once you have the unit, all that's left to do is install it according to the instructions:

• Remove all hoses and wires from the old pressure switch, remembering to take a photo of the correctly connected part;
• remove the screws that secure the relay to the machine body;
• remove the sensor itself.

This procedure will take no more than five minutes of your time and save you money. Install the new part in reverse order, remembering to securely fasten all components and close the top panel of the Midea washing machine tightly. After completing all the steps, all that's left to do is run a test cycle to ensure water is filling the drum again.

   

Readers' comments