Zanussi Washing Machine Repair
Automatic washing machines manufactured under the Zanussi brand have always been known for their high quality and low price. However, due to long-term use, consumer error, or manufacturing defects, these machines sometimes break down and require repair. Repairing Zanussi washing machines should begin with understanding their weaknesses, or more specifically, the most common problems, which is what we'll cover in this article.
Overview of typical breakdowns
As already noted, Zanussi washing machine repairs should begin with typical breakdowns. Most models of these washing machines are quite demanding when it comes to water quality. The most common consumer mistake when purchasing and installing Zanussi appliances is connecting them directly to the water supply. The water in the tap is far from the best quality, and this is not only about hard water; often, rusty water with all sorts of debris flows from the tap, which very quickly clogs the filters of the washing machine.
Important! Some DIYers intentionally remove the filter from the inlet valve when installing a Zanussi machine. This is absolutely not recommended, as dirty water can literally destroy the machine from the inside.
Therefore, the first common cause of Zanussi washing machine failure is clogged filters. Furthermore, these washing machines are equipped with exceptionally poor door locking devices. According to experts, this is one of the most common failures. In this situation, both the mechanism itself and the sensor fail.
As with any other automatic washing machine, the heating element in Zanussi machines can fail. Hard water is considered one of the main causes of this failure, although some experts also point to unsuitable materials used to make the heating element tube. They say this metal attracts even more scale. Finally, the last weak point of Zanussi washing machines is the drive belt. It is recommended to check the belt at least every four years and tighten or replace it if necessary.
Be sure to clean the filters.
All washing machine filters need to be cleaned periodically. If this isn't done for a while, you may encounter a problem. If one of the filters becomes clogged, the washing machine either can't fill with water or doesn't drain properly. The first situation is more common in Zanussi washing machines. What can be done?
- Unscrew the inlet filter located on the water pipe and clean it.
- If you didn't install an inlet filter, the blockage is in the inlet valve filter (where the inlet hose connects to the machine). Remove the top cover of the washing machine and unscrew the inlet valve and filter.
- We unscrew the filter and thoroughly wash its cuff and mesh from dirt, then unscrew the filter with the inlet valve and put it back in place, then close the top cover of the machine.
The delicate inlet filters of Zanussi washing machines can be a nuisance, but they protect the internal components from damage caused by the accumulation of foreign objects and debris brought in with the water. Experts recommend installing an inlet filter with a water softening cartridge directly on the water pipe.
Dirt in a washing machine can accumulate not only from tap water but also from clothing. Sand and dirt aren't the only things that get into the machine along with clothing. Sunflower seed peels, coins, hairpins, and buttons can also settle in the drain filter. All of these items can stop the machine from working at any moment. Experts recommend manually cleaning the machine after 2-3 washes. clean the drain filter, preventing it from becoming littered.
Please note! Before washing, always check the pockets of items you place in your Zanussi washing machine; foreign objects can damage the internal components of your "home helper."
The hatch locking device has failed.
The device that locks the door of a Zanussi washing machine can fail due to careless handling, a manufacturing defect, or wear and tear. The main problem occurs with the mating part of the device. The plastic part that holds the plates is rather flimsy and breaks if you close the hatch too quickly and with force. The hook remains intact because it's made of metal, but the locking mechanism breaks, making washing impossible. How can I fix this myself?
In this case, repairing the sunroof locking device is practically impossible; it will have to be replaced. Its average cost is around $30. It's quite expensive to stock up on such parts, so you first need to remove the old device to be 100% sure it's faulty before you go shopping. How do you remove the old device?
- We open the hatch cover wide.
- To the right of the hatch there is a hole for the locking hook and two screws holding the hatch locking device, these need to be unscrewed.
- Next, pry up and remove the clamp holding the door seal (the large rubber band around the washing machine door). The easiest way to pry up the clamp is with a screwdriver, as it's quite thin and tight, making it difficult to pry up with your fingers.
- After removing the clamp, remove the cuff itself. Use your fingers to pull it out.
- We put our hand between the front wall of the washing machine and the edge of the drum and remove the locking device.
- We inspect it visually, make sure that the plastic part is broken and the plates have popped out, get ready and go to the store with the old device.
- We show it to the seller, buy a new one, come home, and install it in the old one's place. Problem solved!
Please note! Expecting $30 each time is expensive, so please handle your Zanussi washing machine with care. It's best to close the door gently and then press down on its edge until it clicks into place. This ensures a secure and safe locking of the door.
The heating element burned out
The heating element is the weak point of all washing machines, which operate in water containing high levels of mineral salts. Some companies try to protect their machines' heating elements with special polymer coatings. For example, five years ago, Samsung announced heating elements with a polymer coating that supposedly repels scale. Their idea failed miserably, as scale formed on their heating elements just like on other uncoated elements.
If the heating element in a washing machine breaks down, the water in the tank stops heating, and the system may display an E05 error. In washing machines The Zanussi heating element is located at the rear of the tank, so to get to it you will need to remove the rear wall. We first need to check the heating element for functionality. If it's not working, it needs to be removed and a new unit installed. How is this done?
- We unscrew the bolts holding the rear wall of the washing machine body and remove it.
- At the bottom, directly from the tank, there will be two contacts sticking out, from which wires come – this is the heating element.
- Take a multimeter and check the resistance of the heating element. If the device shows zero, you will have to replace the heating element.
- There is a nut between the heating element contacts; it needs to be unscrewed.
- We remove the wires from the heating element.
- Carefully remove the old heating element from its groove. This may be difficult, as it has become stuck in place over time.
- Spray WD-40 lubricant into the gaps to the right and left of the contacts and use rocking motions to pull out the old heating element.
- Remove all the scale and dirt that you can reach through the hole that has formed, and don’t forget to wipe the edges of the hole with a clean cloth.
- Carefully insert and screw in the new heating element and connect the wires to it.
- We install the back wall in place and check the operation of the washing machine.
Important! Buy only original heating elements made specifically for the Zanussi washing machine model you need. There's a risk that the wrong heating element will burn out, taking the control unit with it, making repairs even more expensive.
Problems with the drive belt
The "symptoms" of a drive belt problem include a running motor but a non-rotating drum. As you can imagine, washing is impossible. The engine's hum is unmistakable, but you shouldn't let it idle unnecessarily. What should you do if you have problems with your drive belt?
- First, let's inspect the location of the malfunction by removing the back wall of the washing machine.
- In the opened niche we will see a large round pulley of the drum, on which the belt is put, and below there is a small pulley of the engine, on which the drive belt is also put.
- If the belt is in place but doesn't turn the drum pulley, it's worn out and needs to be replaced. If the belt has slipped, simply replace it.
- We put the belt on the pulleys, put the back wall back in place and check the functionality of the washing machine.
In summary, despite its reliability, Zanussi washing machines have several common problems that consumers encounter most often. These include clogged filters, a broken door lock, a burnt-out heating element, and a worn-out drive belt. If you own a Zanussi washing machine, you should be familiar with how to troubleshoot these issues.
Interesting:
12 reader comments
Add a comment
Headings
Washing machine repair
For buyers
For users
Dishwasher
The smell of burnt wire, plastic or circuit board, black soot near the hole of the UBL hook.
When picking up speed there is a loud noise...
The water supply does not stop.
There are no signs of life in my machine, there is no electricity.
Is there a fuse in the machine?
The machine fills with water and drains it immediately, the display shows E30.
The drum drive belt comes off.
The water and electricity are on, the lights are on, but the car does not turn.
After switching on, the engine starts to run for a few seconds, after which the car goes into standstill.
Konstantin, what was the reason the machine showed no signs of life? I have a similar problem.
The water supply does not stop even when the drum is rotating.
The water supply doesn't stop even when the drum is running. What should I do? The warranty has only expired for a month.