The program on my Indesit washing machine has crashed.

Indesit washing machines often experience inconsistent wash cycles. This can be attributed to unreliable firmware combined with fragile electronics. A malfunction in an Indesit washing machine's software means that the user's favorite cycles simply don't start, or even if they are set, they get lost mid-cycle. Let's look at the causes of this type of malfunction and what to do in this situation.

The simplest ways to fix it

What should you do if the washing program you're constantly running gets messed up? First, don't panic. Call the service center immediately, invite a technician to repair the equipment, or disassemble the machine yourself.

First of all, you should try to fix the problem by performing a number of simple steps.

You can try to restore the washing machine's functionality:

• Restart the machine. First, turn it on and off using the button. If that doesn't work, unplug the power cord and leave the machine for 15-20 minutes;
• by turning on the test wash;
• by launching the SMA self-diagnosis system.

So, the first thing you should do is reboot the machine. First, try turning it off by pressing the power button. Wait about 20 seconds, then start the washing machine. Set the desired wash cycle. If you can't set the desired program, unplug the appliance. You'll have to wait a little longer—about 15-20 minutes. In some cases, a simple reboot of the washing machine can help resolve a washing machine malfunction.

Certain Indesit washing machine models come with pre-programmed test wash cycles. Most washing machines also feature a self-diagnostic system for detecting potential problems. The manufacturer included these features to help users independently identify the cause of any malfunctions. These programs will only resolve the issue in 10% of cases, as their primary purpose is to identify the problem, not to fix it. However, identifying the cause of the problem is also helpful; it will save you time and give you direction on how to proceed. How do I set up and run the test? To enter diagnostic mode:

• set the programmer knob to position 1 and press the “On” button;
• move the selector to position 2 and turn off the machine;
• switch the programmer back to position 1, turn on the machine;
• after – 3 and turn off the CM;
• again set the selector handle to position 1, press the start button;
• turn to drain and run service test.

The pause between cycles should not exceed 3 seconds. After the test starts, the washing machine will display an error code. Machines without a display will indicate the error by flashing the indicator lights on the control panel. You can find the error code in the user manual included with the machine.

Defects in electronic components

If the problem persists and the malfunction persists, you should check the control module and power supply wiring. First, you'll need to disassemble the washing machine by removing the front panel. This is necessary to gain easy access to the main electronic unit. Once the module is visible, check all contacts and wires one by one. It's best to begin diagnostics with the On/Off button. If any component on the board raises any suspicion, it's recommended to replace it.

If the cause of the malfunction persists even after this repair, you'll need to check the remaining parts of the washing machine. The problem may lie in a faulty component. We'll explain what to do next.

The failure was caused by a broken part

Very often, a failure of the programmed washing mode is caused by damage to the heating element. The system understands that it will not be possible to heat the water collected in the tank, so it does not start the program. However, in this situation, the washing machine's display should show an error code. You can restore the machine to its previous operation by replacing the faulty heating element.

If, after removing the heating element, you find a layer of scale on it, replace it with a new heater.

A faulty electric motor can cause the program to malfunction. It's recommended to entrust motor diagnostics and repair to an experienced technician. After inspecting the component, a professional will determine whether the motor can be repaired or replaced.

Another possible cause of failure is a faulty drain pump. The pump should be checked with a multimeter. If a faulty pump or faulty connections to various sensors is detected, the damaged wiring, contacts, or pump sensor itself should be replaced as soon as possible.

There are several reasons why user programs on Indesit washing machines fail. Such malfunctions can indicate both temporary system issues, resolved by rebooting, and serious damage to internal components. It's best to start with the simplest issues and gradually move on to more complex diagnostics.

   

Readers' comments