There's no water in the washing machine - what should I do?
Have you started washing and noticed that water isn't filling, or is filling very slowly? These problems sometimes occur. This usually happens after a few years of using the washing machine, or after problems with cold water. How can you identify this problem?
Usually, everything is obvious. You turn on the washing machine, set the program, and press start. After that, water should start filling. But what if water doesn't fill the washing machine, or it does, but very slowly? In this article, we'll look at the main causes of this problem and how to fix them yourself.
Reasons for failure
The first reason would be the lack of cold water or weak pressure. If the water pressure is low, the water will flow very slowly. This can cause the laundry process to take hours. Try turning the cold water on full blast in the faucet and check the flow rate. 
If the flow is very weak or there's no water at all, then we've found our problem. Of course, we can't solve it directly. After all, we don't control the water supply to the house. There are two possible solutions:
- Just wait for the water to come back on. Sometimes the water is turned off during various repairs.
- Call your housing office and inquire about the cause of the problem and the timeframe for fixing it. It's also possible that they're unaware of any water supply issues in your building. So, just in case, it's best to call. This will increase the chances that your plumbing will be working properly again quickly.
The water supply is closed or not fully open
Check the position of the tap that controls the flow of water into the washing machine. If it's closed, or open but not all the way, all you need to do is open it. This might answer the question of why water isn't getting into the washing machine. This step will solve the problem. The faucet itself may also be faulty. In this case, it may not open (stuck), or the valve may simply spin. In this case, you'll need to replace the faulty faucet with a working one. These faucets are sold at plumbing supply stores.
The hatch is not closed tightly or the lock is faulty
Try opening and closing the door by pressing firmly. It's possible that the door wasn't closed. The washing machine won't start washing while it's open.
There may also be faulty locking or latching issues. If the washing machine door doesn't stay closed, the guide located under the locking tab may be damaged. This can occur with prolonged use. Repeated opening and closing of the door can damage the hinges. This can cause the door to become misaligned.
You can watch the video instructions for replacing the lock:
Another possible damage is that the tongue (clamp), which looks like a hook, may change its position.
That is, it becomes warped. When warped, it doesn't fit into the proper hole and doesn't lock the hatch closed. This malfunction occurs when the metal rod falls out.
This rod is located on the inside of the washing machine door. It holds the tab in the correct position. If it falls out, the tab will no longer be in the correct position. To fix this problem, you need to disassemble the door and return the rod to its correct position.
Filter or inlet valve defective
Another possible cause is that the filter may be so clogged that it's blocking water flow. In this case, turn off the water supply and remove the inlet hose. This is where the hose connects to the washing machine. The inlet valve filter is located here. It looks like a fine mesh. If this mesh is clogged, it needs to be cleaned and rinsed. If it's fine, we can continue to investigate the cause of the poor water supply.
It's possible your intake valve itself is faulty. It can be repaired, but it's much easier to just buy a new one and replace the faulty one.
The most unpleasant thing, perhaps, would be a breakdown of the control module. In this case, specialized skills are essential. Self-repair or replacement of the module is not recommended for those without specialized knowledge and skills. Therefore, in this case, it is necessary to contact specialists. The module is one of the most expensive parts of the washing machine. Most appliance repair services prefer to replace the module rather than repair it. This repair can be quite expensive, but is often cheaper than buying a new machine.
Heating element and level sensor
Another problem that can cause this breakdown is a faulty heating element, also known as a heating element. You can see how to replace it in the following video:
A broken water level sensor could also be the cause. This device stops the water intake when the machine's water level has reached the required level. If the water level sensor is broken, it must be replaced with a new one. A video instruction on the entire replacement process is included below:
Good luck with your home appliance repairs!
Interesting:
31 reader comments
Add a comment
Headings
Washing machine repair
For buyers
For users
Dishwasher
We couldn't get the filter out. We tried rinsing it out with a small enema. It worked. It pours like Niagara.
How can this be done, with an enema?
break it!
After turning on the washer, it starts filling with water for 2-5 seconds and then stops. Then it stops and nothing happens. I checked the water level sensor. If I remove it from the circuit (simply unplug it), the water fills and the machine doesn't stop. Could this be a faulty water level sensor?
There's debris in the corrugated tube from the drum to the drain pump. It's preventing the ball from closing. Turn the machine on its side and you'll see the corrugated tube underneath. Remove it, clean it, and put it back.
Ariston AVSL 105 washing machine. When turned on, the inlet valve only receives a short pulse (one second). That is, a small amount of water flows, and that's it. And then, silence...
Hello! We just installed the washing machine. We connected everything, set the program, and the drum is spinning, but there's no water coming out. The pressure is good and it reaches the valve, but it won't open. What could be the cause? Please help!
It happens that even in new machines the valve does not work.
How much water should a Bosch MAXX-4 washing machine contain?
Hello! My washing machine is broken. The wash cycle isn't working, but the rinse cycle is. What should I do?
Think for yourself.
The rinse function does not work.
Hello. My washing machine isn't filling with water. Error code F09. What should I do? Please help.
If you have an Ariston, there's a problem with the control module. Either bad connections or a voltage issue.
Hello! My washing machine fills with water for a couple of seconds, then displays error code F08. All the wash cycle buttons (wash, rinse, and spin) are lit up at the same time.
Good afternoon, when turned on, the machine hums but does not fill with water.
I have the same thing.
Hello! Could you please tell me what's wrong with my Bauknecht washing machine and how to fix it? When I turn it on, no water flows and the light indicating the door is sealed doesn't come on. The drum is still spinning.
Hello. My Gorenje washing machine is not supplying water. Could this be related to the pump?
Ardo machine. It's not filling. Please explain the cause. Model 1010.
My Samsung washing machine is full, but water is leaking onto the floor instead of into the machine. What should I do?
The Samsung does not spin the drum and does not fill with water, but the lights are on.
I called a mechanic and they said they needed photocopies of the car documents, my passport, and the registration number, with my signature on each page. This is the first time I've heard of that. Maybe they'd also like copies of the apartment documents? With my signature.
Hello! My Indesit washing machine always displays an H2O error during the rinse cycle. I don't know what to do.
Hello, I have a Zanusi machine. Water isn't flowing into the rinse aid compartment. What should I do?
I turn on the machine, but no water comes out. It starts filling after 5-10 minutes.
Hello, why isn't water getting into the machine? My Atlant is showing error F8 and then F15.
Hello, I have a Beko washing machine. The drum is spinning without water and all the buttons are lit up. What should I do?
In the daily wash mode, it does not fill with water and just hums.
Then it shows error code 4c.
Ariston Hotpoint washing machine, two months old, was washing fine, but now I turn on the wash cycle and the water starts filling up and the machine locks. The drain works, but it's also intermittent. I've restarted the machine, but nothing happens. Is it the brain or something else?
Hello, my washing machine isn't filling with water. There's a quick burst of water, but then nothing happens. It's an Ariston AVSL80. Please help.