How to start a Beko tumble dryer for the first time

It's important to properly start up your Beko tumble dryer for the first time. Many users aren't even aware that there are some nuances to consider. We'll explain what owners of a brand-new "home helper" need to know.

Installing a new tumble dryer

First-time use guidelines apply not only to washing machines but also to dryers. Any appliance requires preparation before use. This also applies to automatic clothes dryers.

Before using your new dryer, be sure to read the instructions for the equipment.

The user manual describes all the details of preparing, installing, and connecting the model. It also answers all your questions. The first pages of the brochure provide information about the dryer's design and recommendations for commissioning.

Modern Beko dryers do not require a drain connection. They are equipped with a condensate collection tank. All you need to operate the dryer is a separate outlet designed for increased load. You cannot connect the device through an extension cord - it is unsafe.

If desired, the device can be connected to a sewer line. This eliminates the need to constantly drain the tank. The condensate will drain directly into the pipe.

Beko manufacturer provides the following recommendations regarding the installation of tumble dryers:

• It is better to place the dryer next to or in a column with the washing machine, so it will be easier to transfer wet laundry from one drum to another;
• It is important to ensure free air circulation around the dryer; do not place it in a closet or lean it close to furniture or other equipment;
• the dryer must stand level (it is better to check this using a building level), the position of the body can be changed using adjustable feet;
• Do not remove the dryer's legs or place it on the floor with its bottom on the floor - this will hinder air flow and lead to overheating of the equipment;
• It is prohibited to install the machine on a carpeted surface - this will also disrupt air circulation and may cause a fire;
• A separate grounded outlet is required to power the dryer;
• It is recommended to connect the machine to the network through a voltage stabilizer.

Once installation is complete, check the machine for stability. Press down on each corner of the body one at a time. The dryer should not wobble. If it does wobble, continue adjusting the feet.

Let's start using the dryer

Once installation is complete, you can use the dryer for the first time. First, wipe the inside of the drum with a soapy sponge, then with a damp cloth. There may be dust from the factory or the store. Sometimes grease remains inside, which can ruin your clean laundry. Therefore, don't neglect this step.

It's also important to understand the software inside your new Beko dryer. A description of all the algorithms is included in the equipment manual. You need to understand which modes are suitable for which fabrics and the temperature to which the air inside the machine is heated.

It's important to understand what programs are stored in your Beko model's memory – each type of laundry has its own drying mode.

Now your "home assistant" is ready to be used. Transfer your laundry from the washer to the dryer, close the door tightly, and select the appropriate program. If necessary, activate additional functions.

What advice does the manufacturer offer regarding the operation of a Beko dryer? There are quite a few. Let's look at the main ones.

• Avoid loading items that are too wet (dripping water) into the washing machine. Always spin the items first (even when hand-washing). This will reduce drying time. It will also reduce the strain on the heating element. It will also be safer for both the user and the machine itself.
• Be sure to select the drying mode based on the type of laundry you're loading into the drum. This will prevent you from ruining your favorite items.
• If your clothes have locks, buttons, or snaps, they need to be fastened (if you didn’t do this during the washing process).
• Be sure to read the list of items that should not be tumble dried. These include genuine and faux leather, suede, and rubber. Besides damaging the items, some materials can even cause a fire.
• Avoid overdrying your laundry. After a long time in the washing machine, the fabric will not iron properly. Items may also shrink by 1, and sometimes even 2, sizes.
• It's best to wait 5-10 minutes after the drying cycle is complete before unloading dry laundry. Opening the door immediately can cause burns from hot steam.
• Don't overload the dryer - your clothes won't dry, and your time and kilowatts will be wasted.
• Overloading the dryer can also lead to equipment failure and costly repairs.
• Clean your dryer's lint filter regularly, approximately after every 2-3 cycles. It's located just inside the dryer door. The filter shouldn't be clogged, as this will restrict air circulation.
• Don't forget to check and empty the condensate container.

To eliminate any questions about how to turn on your dryer for the first time, let's break it down step by step. It's actually quite simple.

• Make sure all dryer air vents are accessible.
• Plug the dryer's power cord into a power outlet.
• Place wet, washed items into the drum (observing the maximum permissible load weight).
• Distribute the laundry evenly inside the dryer.
• Close the hatch door tightly.
• Turn on the dryer using the power button and wait until the control panel lights up.
• Select the appropriate drying mode.
• Add additional options to the main program if required.
• Activate the cycle using the Start/Pause button.

Now all that remains is to wait until the machine finishes the cycle. Some programs last 40-50 minutes, others - 2-3 hours, there is no need to check whether the laundry is dry ahead of timeThe dryer will notify you when it has finished using the product with a sound signal.

Finally, the final melody has sounded. What to do next?

• Wait until the dryer control panel lights go out.
• Unplug the machine's power cord from the outlet.
• Open the hatch door and carefully remove the items from the drum.
• Check the condensate collection container and drain the water from the tray.
• Remove and clean the lint filter (this should be done after every second cycle).

It's a good idea to wipe the inside of the drum with a damp cloth. Hair, threads, lint, and other debris can stick to the walls of the chamber. Leave the door slightly open to allow ventilation.

Don't run the dryer more than twice in a row. This will put a lot of strain on the heating element and cause it to burn out. Therefore, be sure to let the dryer "rest" for at least an hour.

Readers' comments